Mounter and Service Provider
Installation of detectors of the DOKA sensors series
The manufacturer’s many years of experience have allowed us to create products with maximum efficiency and low cost.
Key features of DOKA sensors:
- constantly monitor and adjust its parameters to any operating conditions (dust, interference, temperature);
- constantly testing its own performance;
- keep its sensitivity constant by monitoring and automatically compensating for changes in the measuring module;
- have software and hardware protection against interference from static electricity and electromagnetic radiation;
- have a light indication of at least five states: «Normal operation», «Fire», «Fault», «Dust in Chamber», «Event in Memory»
Why do we recommend interactive mode?
- Step 1
- Step 2
- Step 3
- Outcome
Any change in the “DOKA – c” states is displayed by light indication, and the control panel registers this change using basic signals: “AL (Alarm Loop) is normal”, “AL is open”, “Fire”.
If something occurs in the alarm loop, the control panel signals and registers it in the event log.
The specialist arrives at the facility and, according to the control panel event log, finds in which AL the occasion was registered.
By light indication of all “DOKA – c” in this AL, it must establish which of the alarm box is in a state different from the “Stand-by mode”.
You save your time and money by increasing quality and reliability:
- there is no need to check each alarm box, since the system completely controls itself
- you do not need to spend a lot of time looking for a faulty or triggered alarm box, because “DOKA – c” always remembers and displays its states
- “Doka – c”, which diagnosed dust pollution or a faulty, will unobtrusively report this to the control panel no more than one time a day.
- Step 1
- Step 2
- Step 3
- Outcome
Any change in the “DOKA – c” states is displayed by light indication, and the control panel registers this change using basic signals: “AL (Alarm Loop) is normal”, “AL is open”, “Fire”.
If something occurs in the alarm loop, the control panel signals and registers it in the event log.
The staff on duty calls a representative of the service organization.
The specialist arrives at the facility and, according to the control panel event log, finds in which AL the occasion was registered.
By light indication of all “DOKA – c” in this AL, it must establish which of the alarm box is in a state different from the “Stand-by mode”.
You save your time and money by increasing quality and reliability:
- there is no need to check each alarm box, since the system completely controls itself
- you do not need to spend a lot of time looking for a faulty or triggered alarm box, because “DOKA – c” always remembers and displays its states
- “Doka – c”, which diagnosed dust pollution or a faulty, will unobtrusively report this to the control panel no more than one time a day.
How does it work?
Removal and installation into the base.
- Removal and installation into the base.
- Easy ways to remove it from the base.
DOKA-c in your hands
DOKA-c on the ceiling.
- Removal and installation into the base.
- Easy ways to remove it from the base.
DOKA-c in your hands
DOKA-c on the ceiling.
Mounting
Mounting variants
Specifications
- DOKA - C
- DOKA - A
- DOKA - Т
- DOKA - СТ
Optical smoke detector IP 212-02К “DOKA - c”
The detector is installed in enclosed spaces for continuous smoke detection and transmission of Fire and Fault signals to the fire control panel through a 2 wire loop
Certified:
BY: ТР 2009/013/BY, СТБ 11.16.03
RU: ГОСТ Р 53325-2012
UA: ДСТУ EN 54-7
ISO 9001
| Detector sensitivity | 0.05 - 0.20 dB / m |
| Average area controlled by one detector with a height of the protected room up to 3.5 m | no more than 85 m2 |
| Supply voltage range | 9 ... 24 V |
| Rated supply voltage | 12 V |
| Consumption current in "Standby mode" | no more than 65 μA |
| Consumption current in the "Fire" state (set by the position of jumpers "1" and "2") | 6 ± 1, 15 ± 1, 10 ± 1, 19 ± 2 milliampere |
| Duration of outage to reset the Fire condition | more than 2 s |
| Permissible level of exposure to background illumination | 12000 lx |
| The degree of protection of the detector shell according to GOST (National Standart) 14254 | IP40 |
| Operating temperature range | - 30 ... + 55 °С |
| Relative air humidity at a temperature of +40 ± 2 ° С | 93 ± 3 % |
| Climatic version according to GOST (National Srandart) 15150 | УХЛ 3.1 |
| Immunity to electromagnetic interference | hardness 3 |
| Weight of the detector with base | no more than 0.14 kg |
| dimensions | no more than 90 x 90 x 45 mm |
| Average service life | at least 10 years |
Self contained smoke detector IP 212-03К “DOKA - a
The detector is installed in enclosed spaces for continuous smoke
detection, powered by a built-in battery.
It has a fault indication and low battery signal.
Standards compliant:
RU: ГОСТ Р 53325-2012
EU: EN 14604
ISO 9001
| Battery type | 6F22 |
| Current consumption in ‘‘Normal Operation’’ state | max. 25 µA |
| Guaranteed battery operation | 12 months |
| Sound pressure level | min. 85 dB |
| IP rating | IP40 |
| Operating temperature range | - 10 … + 55 °С |
| Relative humidity at +40 °C | 93 % |
Heat detector IP 101-13К-A2S “DOKA - T”
The detector is installed in enclosed spaces for continuous heat rise detection and transmission of Fire and Fault signals to the fire control panel through a 2 wire loop
Standards compliant:
BY: ТР 2009/013/BY, СТБ 2218
EU: EN 54-5
ISO 9001
| Detector clas | А2S |
| State “Fire” temperature | +54 … +70 °С |
| Supply voltage range | 9 … 24 VDC |
| Current consumption in “Normal Operation” state | max. 50 µA |
| Current consumption in “Fire” state | set from: 5, 10, 15, 20 mA |
| IP rating | IP40 |
| Operating temperature range | - 30 … + 75 ° |
| Relative humidity at +40 °C | 93 % |
Combines optical smoke and heat detector IP 212/101-12К-A2M “DOKA - CT”
The detector is installed in enclosed spaces for continuous smoke and heat detection and transmission of Fire and Fault signals to
the fire control panel through a 2 wire loop
Standards compliant:
BY: ТР 2009/013/BY, СТБ 11.16.03, СТБ 2218
EU: EN 54-7, EN 54-5
ISO 9001
| Detector clas | А2M |
| State “Fire” temperature | +54 … +70 °С |
| Supply voltage range | 9 … 24 VDC |
| Current consumption in ”Normal Operation” state | max. 65 µA |
| Current consumption in ”Fire” state | set from: 5, 10, 15, 20 mA |
| IP rating | IP40 |
| Operating temperature rang | - 30 … + 75 ° |
| Relative humidity at +40 °C | 93 % |
- DOKA - C
- DOKA - A
- DOKA - Т
- DOKA - СТ
Optical smoke detector IP 212-02К “DOKA - c”
The detector is installed in enclosed spaces for continuous smoke detection and transmission of Fire and Fault signals to the fire control panel through a 2 wire loop
Certified:
BY: ТР 2009/013/BY, СТБ 11.16.03
RU: ГОСТ Р 53325-2012
UA: ДСТУ EN 54-7
ISO 9001
| Detector sensitivity | 0.05 - 0.20 dB / m |
| Average area controlled by one detector with a height of the protected room up to 3.5 m | no more than 85 m2 |
| Supply voltage range | 9 ... 24 V |
| Rated supply voltage | 12 V |
| Consumption current in "Standby mode" | no more than 65 μA |
| Consumption current in the "Fire" state (set by the position of jumpers "1" and "2") | 6 ± 1, 15 ± 1, 10 ± 1, 19 ± 2 milliampere |
| Duration of outage to reset the Fire condition | more than 2 s |
| Permissible level of exposure to background illumination | 12000 lx |
| The degree of protection of the detector shell according to GOST (National Standart) 14254 | IP40 |
| Operating temperature range | - 30 ... + 55 °С |
| Relative air humidity at a temperature of +40 ± 2 ° С | 93 ± 3 % |
| Climatic version according to GOST (National Srandart) 15150 | УХЛ 3.1 |
| Immunity to electromagnetic interference | hardness 3 |
| Weight of the detector with base | no more than 0.14 kg |
| dimensions | no more than 90 x 90 x 45 mm |
| Average service life | at least 10 years |
Self contained smoke detector IP 212-03К “DOKA - a
The detector is installed in enclosed spaces for continuous smoke
detection, powered by a built-in battery.
It has a fault indication and low battery signal.
Standards compliant:
RU: ГОСТ Р 53325-2012
EU: EN 14604
ISO 9001
| Battery type | 6F22 |
| Current consumption in ‘‘Normal Operation’’ state | max. 25 µA |
| Guaranteed battery operation | 12 months |
| Sound pressure level | min. 85 dB |
| IP rating | IP40 |
| Operating temperature range | - 10 … + 55 °С |
| Relative humidity at +40 °C | 93 % |
Heat detector IP 101-13К-A2S “DOKA - T”
The detector is installed in enclosed spaces for continuous heat rise detection and transmission of Fire and Fault signals to the fire control panel through a 2 wire loop
Standards compliant:
BY: ТР 2009/013/BY, СТБ 2218
EU: EN 54-5
ISO 9001
| Detector clas | А2S |
| State “Fire” temperature | +54 … +70 °С |
| Supply voltage range | 9 … 24 VDC |
| Current consumption in “Normal Operation” state | max. 50 µA |
| Current consumption in “Fire” state | set from: 5, 10, 15, 20 mA |
| IP rating | IP40 |
| Operating temperature range | - 30 … + 75 ° |
| Relative humidity at +40 °C | 93 % |
Combines optical smoke and heat detector IP 212/101-12К-A2M “DOKA - CT”
The detector is installed in enclosed spaces for continuous smoke and heat detection and transmission of Fire and Fault signals to
the fire control panel through a 2 wire loop
Standards compliant:
BY: ТР 2009/013/BY, СТБ 11.16.03, СТБ 2218
EU: EN 54-7, EN 54-5
ISO 9001
| Detector clas | А2M |
| State “Fire” temperature | +54 … +70 °С |
| Supply voltage range | 9 … 24 VDC |
| Current consumption in ”Normal Operation” state | max. 65 µA |
| Current consumption in ”Fire” state | set from: 5, 10, 15, 20 mA |
| IP rating | IP40 |
| Operating temperature rang | - 30 … + 75 ° |
| Relative humidity at +40 °C | 93 % |
